S M Engineering Works provides wide array of modular Cement Testing Equipment our complete cement testing instruments and Cement Testing Equipment range includes accelerated curing tank, vibrating table, compaction factor apparatus, Compression testing machine, concrete penetrometer, cube mould, cylindrical mould, vicat needle apparatus etc.
Standards:
Product Description: Marsh funnel is a simple yet important apparatus to measure the viscosity of the slurry and other types of cement mixes. Viscosity is a determinant of the flow speed and thickness of the slurry and therefore also its strength characteristics. The dimensional make of marsh funnel and measuring cup is precisely maintained as per the demands of mud engineers who use it to measure the viscosity of fluidized mixes of different types.
Specification:
Standards: ASTM D 4381
Specification: One of the primary functions of a drilling fluid is to carry drilled solids from the well bore. These solids are a contaminant, and if left in the system, can lead to numerous problems. The offsite sand content kit determines the volume percent of sand-sized particles in the drilling fluid. Api defines sand-sized particles as any material larger than 74 μm (200-mesh) in size. The test can be performed on low solids fluids as well as on weighted fluids. The kit consists of a glass tube graduated to read percent (%) by volume, a funnel, and a 200-mesh sieve contained in a cylindrical shaped holder. Consists of sand content kit, complete, with sieve, funnel, graduated tube, wash bottle & carrying case.
Standards:
Product Description: It provides a simple method for the accurate determination of mud density. The balance consists of a base and graduated arm with cup, lid, knife edge, rider, built-in spirit level and counter-weight, carrying case. The constant volume cup is affixed to one end of the graduate arm and the counter-weight on the opposite end. The apparatus has –
Specification: Reading of the specific gravity of the semi liquid is thus derived instantaneously. Simple to use, this apparatus offers on the spot measurement of density and this in turn helps the engineers to make the relative comparisons for the purpose of project execution.
Standards:
Specification: This is the core of the system. A continous discharge vacuum pump is complete self contained unit. The unit is mounted on a transportation truly 24 Sq. Meter freshly laid concrete can be Dewatered in one single operation with one set mat. The pump is powered by 7.5 HP 3 Phase Electric Motor.
Technical Details:
Model | Length | Width | Height | Weight | Max. Dewatering Capacity | Prime Mover | Power Rating |
---|---|---|---|---|---|---|---|
SMEW-501 | 1200mm | 500mm | 800mm | 110kg | 30 sq.mt | Electric | 7.5 HP/Motors |
Standards: IS 1199-1959, IS 4031 1968 BS 1881, ASTM C 151, C490.
Specification: The instrument consists of a channeled or a round base over which two vertical pillars are fixed. An adjustable cross plate is at the top. A dial gauge, reading to .002mm x 5mm. Can be located upon a 6.5mm. dia ball or other reference point cemented in the specimen. On the base there is similar recessed seating in which can be placed a second ball or reference point in the specimen. Complete with a stainless steel standardization bar with insulated grip and with 6.5mm dia. Balls mounted in the ends. The unit can be supplied with an Electronic Dial Gauge at extra cost if indicated at the time of placing the order.
Standards: ASTM C 490, IS 4031 & BS 1881.
Specification: The apparatus comprises of one mould effective gauge length complete with base plate, four reference pins, one length comparator frame, one stainless reference bar with insulated grip, and one dial gauge, 0.002mm x 5mm
Standards: IS 4031-1968, IS 1624-1960 & ASTM C 151, C 141
Specification: The autoclave is suitable for conducting accelerated soundness tests on cements or the autoclave expansion test requiring constant steam pressure with the correspondent constant pressure. It consists of a stainless steel cylinder with a welded heat insulated metal housing attractively finished. The attached control unit encloses a sensitive pressure regulator and pressure gauge. Power switches and pilot lights for controlling the electric heating units. Inside chamber dimensions 10.5 cm diameter x 40.5cm height suitable for operation on 230 V, 50 Hz Single Phase A. C. supply. Supplied complete with test bar holder, special rack to hold specimens above water level in the autoclave and in a vertical position to expose them in the same manner. A Digital PID Controller is fitted for controlling the desired temperature.
Note: Ordinary laboratory cement autoclave with mild steel chambers are also available
Standards: IS 11262-1985, ASTM C 186
Specification: This equipment is required to determine the heat of hydration of cement as expressed in calories per gram. The equipment comprises of the following:
Standards: IS 1727 1967, IS 4031 1968, ASTM C 394, C 64
Specification: It is supplied complete with base. All parts are marked with the identification number for correct assembly. Each mould is individually verified in the dimensional tolerances, hardness, squareness, flatness & roughness. Size: 40.1 X 40 X 160 mm
This very robust mixer is expressly designed for the efficient mixing of cement pastes and mortar, with four automatic sequences of mixing cycle, in compliance with: EN 196-1, EN 196-3:2005, EN 480-1 Specifications. Bowl capacity is 4.7 litres
Two speeds can be selected:
By operating automatically on changes of speed, stops and mixing sequences, outlined by acoustic signal, the unit performs the mixing cycle. The unit is equipped with an automatic sand dispenser which fills the sand into the mixing bowl for a period of 30 seconds (EN 196-1 program). Complete with safety door conforming to CE Safety Directive; if opened it automatically stops the machine. Supplied complete with stainless steel bowl, but without beater which has to be ordered separately (see mod. E095-03 or E095-05).
Product Description: The machine consists of a vibrating frame assembly and an electric motor mounted on a sturdy base. The complete frame assembly consists of a vice to hold a 70.6 mm cube mould and two studs threaded at top and a hopper to feed the sample in the mould. This assembly is supported on four springs and has an in built rotating shaft which rotates eccentrically and thus imparts vibrations to the entire frame. A balance weight is an integral bottom part of the frame. The centre of gravity of the assembly is brought to the centre of the eccentric shaft within a distance of 25 mm below it. The electric motor drives the shaft of the frame and thus imparts required vibration to the moulds. The frequency of vibration is 12000 +/- 400 Vibration Per Minute. Supplied complete with on 70.6 mm Cube Mould with loose base plate, a time switch 0-5mins x 1mm. Spares: Set of springs, belt and belt guard. Optional: Digital Preset Timer can be supplied at an extra cost.
Specification:
High Performance Vibrating Machine: Complete apparatus is available including the different components like mortar cube, belt cover, balance weight, springs set, base plate and a digital timer device. The complete testing apparatus is tested for accuracy and stable performance before it is moved out of the production line at our manufacturing facility.
Standards: BS 12, IS 4031
Specification: Weight approximately 210 gms.. Best quality with hard wood handle blade length 200mm.
Standards: BSl2
Specification: The instrument employs a friction free, accurate, double lever system, the load being applied by means of sliding weight on the top lever. The capacity of the units is 900 kgs. After fixing the briquette in the jaws, the machine is switched on. The sliding weight slides over the calibrated lever thus applying tension to the specimen. A micro switch fitted instantly stop the machine on failure of the briquette and on failure the tensile load is accurately 0.5kg. By means of a marker provided on the sliding weight to its zero position. Suitable for operation on 230 V, 50 cycles, Single Phase, A.C. supply. Supplied complete with one brass briquette mould and one base plate.
Standards: IS 269 1958, Bs12
Specification: For casting of cement briquettes for tensile strength tests. It is a two part split mould made of gun metal. Two thumb screws facilitate easy and quick assembling and dismantling of the mould. The minimum cross section of the briquettes cast is 25.4 mm x 25.4 mm. Supplied complete with a steel base plate.
Standards: ASTM C-360
Specification: The apparatus is used to determine the workability of Portland cement & concrete. The Kelly ball test is considered to be simple and much faster than the slump test. Twice the Kelly ball reading approximately equals the slump. It consists of a cylinder with a ball shaped bottom and handle, together weighing 15 kg. A strip frame, guides the handle and serves as a reference for measuring the depth of penetration. The handle is graduated in mm. Penetration can be recorded to the nearest 0.5 mm.
Standards: IS 1727 1967, IS 4031 1968, ASTM C 394, C 64
Specification: The jolting apparatus consists of a rectangular table rigidly connected by two support arms to a spindle at a horizontal distance of 800 mm from the centre of the table. There is a projecting lug with a plane face on the upper face of the table beneath which is a stop with a rounded upper surface. The table can be raised and allowed to fall freely on the stop by a cam which is connected to a motor and gearbox through a V-belt an pulleys. The cam rotates at a rate of 60 Rev/Min. A stroke counter fitted with micro-switch is provided which stops the machine after 60 Jolts. Locating pins are provided for mounting the mould compartments on the table. The mould surmounted by the hopper can be clamped rigidly to the table. Supplied complete with mould and hopper. Suitable for operation on 230 Volts, Single Phase, A.C. Supply. A Digital Preset Counter can be supplied at an extra cost.
Spares and Accessories:
Standards: IS 7535 1986, ASTM C 183, AASHTO T 127
Specification: This is a brass tube approximately 53cm long and 2.8cm I.D. with a wooden handle. Total length approximately 73cm. The tube has the sharp angular edge which conveniently pierces cement bags. An air hole of approximately 3mm dia. is drilled on the tube near handle. Total sample collected at one time is 300 cm approximately.
Standards: IS 4031, 5516, 1727 & 4828, ASTM C-204, BS 4359-2
Specification: Designed to find out specific gravities of semi liquids like mud and other liquids having densities in the range 0.8 to 2.5. It has a stainless steel bam calibrated specific gravities from 0.8 to 2.5. A stainless steel cup with lid and overflow vent is fitted on one side of the beam. A counter weights with cursor slides over the graduated scale. The beam has a knife-edge at centre which rests in a fulcrum fitted in the stand. Leveling screws and spirit level are fitted to the stand.
Spares & Accessories (On Extra Cost):
Punch to cut filter paper discs. Non-perforated disc. Suction bulb, Mercury.
The apparatus consist of metallic frame bearing a freely movable and with a cap at top, one vicat mould and glass base plate and one set of needles one each initial needls, final needle and consistency plunger. It comes with a dashpot which facilities gentle lowering of the needls
Accessories:
Mild steel base plate 5 inchesX 5 inches.
Fulcrum mould, brass, 80 mm i.d base dia x 70 mm i.d top dia, 40mm height
Note:
Standards: IS 712 1956, ASTM C 187
Specification: Consists of mould 100 mm x 5mm. Deep and a glass base plates. Used to determine soundness of hydrated lime
Standards: ASTM C 266
Specification: A base with a Vertical shaft and Two horizontal arms. The lower arms is adjustable for height. 1 no. Initial needle 1/12-inch dia. ¼ lb. Wt. 1 no. Final needle 1/24 inch dia. ¼ lb. Wt. 1 no. Glass base plate. Complete as above.
Standards: IS: 6932 (PART VIII), ASTM C 230, BS 4551:1
Specification: The flow table consists of a 30 cm dia polish steel plate with 3 engraved annular circles 7, 11 and 19cm dia. The table top is arranged for a free fall of 12.5mm by a cam action. Supplied complete with one brass conical mould, 65mm i.d. at base and 40mm i.d. at top, height of the mould 90mm.
Standards: IS 1199-1959, ASTM C-124, AASHTO-T-120.
Specification: Consists of a steel table top 76.2cm ( 30 inch. Dia.) Finely machined. The integral cast ribs are designed for support and strength. The stand is fabricated out of cast iron and is of study construction. Holes for mounting in foundations are drilled in the base plate. The ground and hardened steel cam is designed to fit and drop the table by 12.5mm. Electrically operated to raise and drop the table top, approx. 15 times in 15 seconds, Suitable for operation on 230 Volts, 50 cycles, A.C. supply. Supplied with one conical mould with two handles, 12cm height, having 17cm. Inside Dia. at the Top and 25cm inner dia. at the base. Complete with a tamping rod 16mm dia x 600mm long one end rounded.
Standards: IS 5512 & BS 4551-1
Specification: It consists of a machined brass table top 250+/- 2.5mm dia. Mounted on a rigid stand. The table top is reinforced with equally disposed ribs and allowed to conical brass mould 100mm i.d. top dia and 50mm high.
Accessories: Mild steel plate 25mm thick & 250mm square for fixing to underside of the base
Standards: IS 5512 & BS 4551-1
Specification: Same as SMEW-1008 but electrically operated. Fitted with a motor, connected to the cam shaft through a reduction gear to give approximately 100 R.P.M. Suitable for operation in Single Phase 230 V A.C. 50 Cycles, Supply.
Standards: IS 269, 712, 5514, 1727 , 2645, 6932 ( PART IX) BS 6463
Specification: It consists of a small split cylinder forming a mould. On either side of the split cylinder. Two parallel indicating arms with pointed ends are attached. Supplied complete with two glass plates and a lead weight.
Standards: IS 4031 1968, ASTM C 188
Specification: Used for finding specific gravity of hydraulic cement. Made from Borosilicate glass. The flask is 243mm in total height, having a bulb of 90mm dia. of 250ml approximate capacity. The long neck of the flask has at top a funnel of 50mm dia. in that fits a ground glass stopper. The neck has over-all 11mm i.d. upper portion is graduated from 18ml to 24ml with 1 ml graduation. Just at the bottom of the neck 1 ml capacity is marked in between there is 17 ml capacity bulb.
Standards: IS 4031, 10086, ASTM C 227. & BS 1881.
Specification: Available Models:
Spares: Stainless steel smooth or knurled and threaded reference pins as required. Supplied in Packs of one dozen.